Evaluation of tool wear and machined surface integrity when drilling aluminium alloy 7075 under cold air and dry conditions

Evaluation of tool wear and machined surface integrity when drilling aluminium alloy 7075 under cold air and dry conditions

Saved in:

书目详细资料
主要作者:	Nur Munirah Meera Mydin
格式:	图书
标签:	添加标签没有标签, 成为第一个标记此记录!

相似书籍

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
由: Abd. Rahim, Erween
出版: (2005)

Performance evaluation of uncoated and coated carbide tools when drilling titanium alloy
由: Abd. Rahim, Erween
出版: (2005)

Dry sliding wear of some commercial wrought aluminium alloys /
由: Mariyam Jameelah Ghazali
出版: (2005)

Effect of drill geometry of uncoated tool when drilling titanium alloy, Ti-6Al-4V
由: Rashiddy Wong, Freddawati
出版: (2008)

Comparison of machinability aluminium alloy LM6 when using coated and uncoated carbide cutting tool
由: Khuzaimi, Mohd Aris
出版: (2014)

Characterization Of Fretting Fatigue of 7075-T6 Aluminium Alloy
由: Jacob, M. Suresh Devanesan
出版: (2006)

Machinability study of uncoated and coated carbide tools when drilling CFRP/metal stacks
由: Mahamad Hakimi, Ismail
出版: (2015)

Optimization Of Welding Parameters On Mechanical Properties Of Aluminium Alloy 7075
由: Yomli, Sofia Mulyani
出版: (2019)

Experimental study on the aluminum alloy 7075 during turning under dry and minimal quantity lubrication conditions /
由: Abdul Rahman Abdul Ghani
出版: (2021)

Study of different fillers on aluminium alloys 6061 and 7075 by MIG welding
由: Nur Fakhriah, Mohd Noordin
出版: (2020)

The Influence Of Tool Geometry Towards Cutting Performance On Aluminium 7075
由: Jumali, Muhammad Syafik
出版: (2016)

Wear performance of alumina based cutting tool when machined with AISI 1045 carbon steel
由: Mazda, Nur Syahirah
出版: (2018)

Experimental Studies On Effect Of Process Parameters On Tool Wear In Drilling CFRP Composites With Ultrasonic Machine
由: Mohammed Muslem, Mohammed Bakar
出版: (2019)

Surface modification of aluminium-zinc alloy (AA7075) and its corrosion characteristics /
由: Angel Richard
出版: (2018)

Study on surface retrogression and re-aging (SRRA) behaviour of aluminium alloy 7075
由: Nozmi, Nor Azrin
出版: (2013)

Tool Condition Monitoring Of Drill Bit Wear Using Camera For Composite Assembly In Aerospace Manufacturing System
由: Ramzi, Ahmad Raiminor
出版: (2019)

Optimization of drill geometry design for orthopedic surgical application in dry drilling condition
由: Mohd Samsuddin, Noorazizi
出版: (2017)

Investigating the tribological properties of thin film nitride based PVD coatings on AL7075-T6 alloy under dry-sliding conditions /
由: Quazi, Moinuddin Mohammed
出版: (2013)

Electrodeposition Of Nickel Coatings On Aluminium Alloy 7075 Through A Modified Single Zincating Process
由: Othman, Intan Sharhida
出版: (2016)

Surface integrity study when drilling inconel 718 using coated carbide tool
由: Kamaruzaman, Hasrul Shafiq
出版: (2011)

Direct recycling of aluminium alloy 6061 and 7075 employing cyclic extrusion compression back pressure technique
由: Mohamad Syahmi, Shahrom
出版: (2016)

Progressive tool wear in machining biomedical alloy using uncoated and titanium diboride coated tungsten carbide tools
由: Mohd Hafizu, Zakaria
出版: (2019)

Dry sliding wear behaviour of thixoformed AL-5.7SI-2CU-0.3MG aluminium alloy/
由: Abdelgnel, Mnel A.H

Characterization Of Oil Retrogression Of Aluminum Alloy 7075
由: Ng, Guan Yao
出版: (2014)

Investigation on mechanical and wear properties of strontium modified aluminium-silicon alloy /
由: Adibah Amir
出版: (2008)

Differentiation analysis of surface integrity and wear mechanism AISI 1045 machinability assesment under wet and dry condition
由: Norfauzi, Tamin
出版: (2017)

Effect of tool path generation when machining mold-cavity
由: Sarip, Rohana
出版: (2009)

An experimental study and modeling on gas metal arc welded lap joint of A7075-T651 aluminium alloy to AZ31B magnesium alloy
由: M. Rafiqul, Islam
出版: (2015)

Wear mechanism and surface integrity studies when turning hardened tool steel using wiper coated ceramic tool
由: Umar, Alkali Adam
出版: (2011)

Performance evaluation of drilling aluminium filled epoxy using HSS cutting tool
由: Othman, Tahrin
出版: (2013)

Effect of cutting parameters on the hole diameter and surface roughness for dry drilling of aluminum alloy 6061
由: Ahamed, Ahmad Fauzi
出版: (2010)

Effects of deformation and recrystallization on mechanical properties of 7075 aluminum alloy /
由: Tajally, Mohammad
出版: (2010)

The effect of vibration on metal removal rate and tool wear rate for small hole electrical discharge drilling /
由: Sriani, Tutik
出版: (2008)

Zirconium oxide nanoparticle-reinforced aluminium alloy (AA7075) matrix composites via hot extrusion and equal channel angular pressing
由: Sabbar, Al Rubaiawi Huda Mohammed
出版: (2022)

Modelling of stagnant zone formation on diamond cutting tool when turning titanium alloy
由: Thet, Thet Mon
出版: (2007)

Tool wear and tool life performance of TiA1N coated carbide cutting tools when turning XW 42 hardened tool steel
由: Effendy, Effendy
出版: (2007)

Machinability study of coated and uncoated carbide tools in drilling inconel 718
由: Rival, Rival
出版: (2014)

Machining performance of 22MnB5 Boron steel cutting tool with Al 6061 Aluminium Alloy
由: Mohd Rashid, Mohd Fairuz
出版: (2021)

Mechanical properties of recycling chip aluminium 7075 through powder metallurgy technique
由: Yacob, Fariza Fuziana
出版: (2015)

Effects of Environmental-Friendly Cutting Fluids on Surface Roughness and Tool Wear in Laser-Assisted High Speed Milling of Aluminium Alloy and 316 Stainless Steel
由: Farhana, Yasmin
出版: (2021)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group