Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)

Biomedical grade of titanium alloys are prone to undergo degradation in body fluid environment. Surface coating such as Physical Vapor Deposition (PVD) can serve as one of the alternatives to minimize this issue. Past reports highlighted that coated PVD.layer consists of pores, pin holes and columna...

Full description

Saved in:

Bibliographic Details
Main Author:	Arman Shah Abdullah
Format:	thesis
Language:	eng
Published:	2015
Subjects:	TJ Mechanical engineering and machinery
Online Access:	https://ir.upsi.edu.my/detailsg.php?det=1275
Tags:	Add Tag No Tags, Be the first to tag this record!

id	oai:ir.upsi.edu.my:1275
record_format	uketd_dc
spelling	oai:ir.upsi.edu.my:12752020-02-27 Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR) 2015 Arman Shah Abdullah TJ Mechanical engineering and machinery Biomedical grade of titanium alloys are prone to undergo degradation in body fluid environment. Surface coating such as Physical Vapor Deposition (PVD) can serve as one of the alternatives to minimize this issue. Past reports highlighted that coated PVD.layer consists of pores, pin holes and columnar growth which act as channels for the aggressive medium to attack the substrate. Duplex and multilayer coatings seem able to address this issue at certain extent but at the expense of manufacturing time and cost. In the present work, the effect of ultrasonic vibration parameters on PVD-Titanium Nitride (TiN) coated Ti-13Zr-13Nb biomedical alloy was studied. Disk type samples were prepared and coated with TiN at various conditions: bias voltage (-125V), substrate temperature (100 to 300C) and nitrogen gas flow rate (100 to 300 seem). Ultrasonic vibration was then subsequently applied on extreme high and low conditions of TiN coated samples at two different frequencies (8 kHz, 16 kHz) and three set of exposure times (5 min, 8 min, 11 min). Encouraging results of PVD coating are observed on the samples coated at higher polarity of nitrogen gas flow rate (300 seem) and substrate temperature (300C) in terms of providing better surface morphology and roughness, coating thickness and adhesion strength. All TiN coated samples treated with ultrasonic vibration exhibit higher corrosion resistance than the untreated ones. Microstructure analysis under (Field Emission Scanning Electron Microscopy (FESEM) confirms that the higher ultrasonic frequency (16 kHz) and the longer exposure time (11 minutes) produce the most compact coating. It is believed that hammering effect from ultrasonic vibration reduces the micro channels' size in the coating and thus decelerates the corrosion attack. Nano indentation test conducted on the ultrasonic treated samples provides a higher Hardness/Elasticity (H/E) ratio than untreated ones. This suggests that the ultrasonic vibration treated samples could also have a lower wear rate. 2015 thesis https://ir.upsi.edu.my/detailsg.php?det=1275 https://ir.upsi.edu.my/detailsg.php?det=1275 text eng closedAccess Doctoral Universiti Teknologi Malaysia Fakulti Kejuruteraan Mekanikal N/A
institution	Universiti Pendidikan Sultan Idris
collection	UPSI Digital Repository
language	eng
topic	TJ Mechanical engineering and machinery
spellingShingle	TJ Mechanical engineering and machinery Arman Shah Abdullah Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)
description	Biomedical grade of titanium alloys are prone to undergo degradation in body fluid environment. Surface coating such as Physical Vapor Deposition (PVD) can serve as one of the alternatives to minimize this issue. Past reports highlighted that coated PVD.layer consists of pores, pin holes and columnar growth which act as channels for the aggressive medium to attack the substrate. Duplex and multilayer coatings seem able to address this issue at certain extent but at the expense of manufacturing time and cost. In the present work, the effect of ultrasonic vibration parameters on PVD-Titanium Nitride (TiN) coated Ti-13Zr-13Nb biomedical alloy was studied. Disk type samples were prepared and coated with TiN at various conditions: bias voltage (-125V), substrate temperature (100 to 300C) and nitrogen gas flow rate (100 to 300 seem). Ultrasonic vibration was then subsequently applied on extreme high and low conditions of TiN coated samples at two different frequencies (8 kHz, 16 kHz) and three set of exposure times (5 min, 8 min, 11 min). Encouraging results of PVD coating are observed on the samples coated at higher polarity of nitrogen gas flow rate (300 seem) and substrate temperature (300C) in terms of providing better surface morphology and roughness, coating thickness and adhesion strength. All TiN coated samples treated with ultrasonic vibration exhibit higher corrosion resistance than the untreated ones. Microstructure analysis under (Field Emission Scanning Electron Microscopy (FESEM) confirms that the higher ultrasonic frequency (16 kHz) and the longer exposure time (11 minutes) produce the most compact coating. It is believed that hammering effect from ultrasonic vibration reduces the micro channels' size in the coating and thus decelerates the corrosion attack. Nano indentation test conducted on the ultrasonic treated samples provides a higher Hardness/Elasticity (H/E) ratio than untreated ones. This suggests that the ultrasonic vibration treated samples could also have a lower wear rate.
format	thesis
qualification_name
qualification_level	Doctorate
author	Arman Shah Abdullah
author_facet	Arman Shah Abdullah
author_sort	Arman Shah Abdullah
title	Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)
title_short	Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)
title_full	Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)
title_fullStr	Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)
title_full_unstemmed	Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)
title_sort	influence of ultrasonic vibration on tin coated biomedical ti-13zr-13nb alloy (ir)
granting_institution	Universiti Teknologi Malaysia
granting_department	Fakulti Kejuruteraan Mekanikal
publishDate	2015
url	https://ir.upsi.edu.my/detailsg.php?det=1275
_version_	1747832963573219328

Influence of ultrasonic vibration on tin coated Biomedical TI-13Zr-13Nb Alloy (IR)

Similar Items