Automated generation of lifters for injection moulds /

Automated generation of lifters for injection moulds /

Saved in:

书目详细资料
主要作者:	Liu, Haihua
格式:	Thesis 图书
语言:	English
出版:	1999
标签:	添加标签没有标签, 成为第一个标记此记录!

相似书籍

Automatic side core creation for designing slider/lifter of injection moulds /
由: Wang, Yong
出版: (1997)

A study on plastic injection mould design : Runner optimization and balancing in a family mould /
由: Daneshkadivar, Mohammadreza
出版: (2000)

An information management system for plastic injection mould design /
由: Guo, Huaqun
出版: (2000)

Computer-aided process planning for the manufacture of injection moulds /
由: Alam, Mohammad Rabiul
出版: (2001)

Feature and associativity-based computer-aided design for plastic injection moulds /
由: Ye, Xiangao
出版: (2000)

Design and development of an integrated mixing and injection moulding machine for micro metal parts /
由: Alhaji, Abdullahi Aliyu
出版: (2017)

3D initial design of plastic injection moulds using standarization techniques /
由: Low, Maria Leng Hwa
出版: (2002)

Optimization Of Injection Moulding Process For Hdpe Moulded Gear
由: Kassim, Mohd Syahir Mohd
出版: (2015)

Automated generation of core and cavity for injection molded parts /
由: Narasa Ramasamy Anantha Narayanan
出版: (1997)

Simulation of plastic injection moulding of family mould using moldflow and design of experiment
由: Mohd. Badri , Mohd. Najib
出版: (2010)

Injection moulding and thermal properties of polypropylene hinges
由: Othman, Mohd Hilmi
出版: (2008)

Effect Of Injection Moulding Parameters On Warpage Deflection
由: Mohd Sani, Siti Salmah
出版: (2015)

Process optimization in rubber injection moulding manufacturing /
由: Ng, Yeow Chian
出版: (2019)

Plastic injection moulding sector in Selangor : a strategic analysis /
由: Tan, Joo Him
出版: (1998)

Numerical simulation of injection moulding : non-isothermal non-Newtonian flow of polymers in complex geometries /
由: Sitters, Cornelius Wilhelmus Maria, 1953-
出版: (1988)

Design and Analysis of Plastic Injection Mould for Holder Casing
由: Wong, Choon Tat
出版: (2004)

Intelligent ejector system design for plastic injection mould /
由: Wang, Zheng
出版: (1997)

Investigation of mould design and process parameter optimisation of plastic injection moulding for thin wall part
由: Hussin, Azmee
出版: (2019)

Optimization of injection moulding parameters for recycled high density polyethylene
由: Ramle, Zuraimi
出版: (2017)

Effect Of Injection Moulding Parameters On The Shrinkage Using Taguchi Method
由: Wan Azhari, Wan Noor Azrina
出版: (2016)

Automated Core And Cavity Design System For Mould Works Using Generative Method Of Computer Aided Process Planning
由: Md Yusof, Mursyidah
出版: (2017)

Automated Core And Cavity Design System For Mould Works Using Generative Method Of Computer Aided Process Planning
由: Md Yusof, Mursyidah
出版: (2017)

Properties of wood plastic composite produced using injection moulding process
由: Hang, Chit Meng
出版: (2010)

Computer simulation of melt flow at the entry region of the injection moulding process /
由: Loh, Leonard Kwok Weng
出版: (1991)

Optimisation of injection moulding process parameters using taguchi and desirability function
由: Vivekanandan, Panneerselvam
出版: (2020)

Performance evaluation of conformal and straight cooling channels on injection moulded part
由: Abd. Rahim, Shayfull Zamree
出版: (2015)

Cost analysis software development for injection moulding in the concurrent engineering environment
由: Zamrah, Zarak Shaifuddin
出版: (2009)

Determination of optimal 3-D parting in plastic injection mould design /
由: Fu, Mingwang
出版: (1998)

Analysis of electromagnetic characteristic of metal injection moulded micro-motor stators /
由: Chau, Hock Chang
出版: (2001)

Design, Analysis and Fabrication of Plastic Injection Mould for Tensile Test Specimen
由: Mohd Ariffin, Mohd Khairol Anuar
出版: (2001)

Simulation of plastic injection moulding part using moldflow and design of experiment
由: Halim , Shamsul Azwan
出版: (2010)

Computer-aided cutter selection and electrode design for mould machining /
由: Ding, Xiaoming
出版: (2001)

Microstructures and properties of CoCrMo alloy by metal injection moulding process
由: Nur Aidah Nabihah, Dandang
出版: (2019)

Injection moulding parameters and performance of rice husk-high density polyethylene composite
由: Mat Isa, Naurah
出版: (2006)

Compounding, injection moulding and characterisation of mangrove particle/high density polyethylene composites /
由: Adebayo, Ganiyat Olusola
出版: (2019)

Injection moulding simulation of wood–filled polypropylene thin-walled composite parts
由: Md Deros, Mohd Azaman
出版: (2015)

Rotation moulding of a hollow femur for 3-D photoelastic stress analysis /
由: Lau, Chung Yin
出版: (1998)

Evaluation of shrinkage and weld line strength on thick flat part in injection moulding process

Stainless steel 316lhydroxyapatite composite via metal injection moulding : properties study
由: Nurul Ain, Johari
出版: (2021)

An improved grey wolf optimiser sine cosine algorithm for minimisation of injection moulding shrinkage
由: Mohd. Hatta, Noramalina
出版: (2019)

Services hosted by the Perpustakaan Sultan Abdul Samad, Universiti Putra Malaysia with Cooperation MySyL Group